close
close

Blind Bolt Fastener, High Strength, Friction Thread Lock, Threaded, 100° Flush Tension Head, Titanium/A-286 (95 KSI Shear)

Unit of Measure

Nominal Diameter

N/A 0.3130 Inch

Nominal Diameter No.

N/A 10

A Theo Inter Ref.

N/A 0.6335 Inch

J Max.

N/A 0.015 Inch

C Driver Length Ref.

N/A 0.350 Inch

D Shank Dia.

N/A 0.3110 Inch0.3120 Inch

E Spline O.D. Ref.

N/A 0.275 Inch

F Head Height Ref.

N/A 0.135 Inch

R Radius Max.

N/A 0.025 Inch

G Gauge Dia.

N/A 0.5449 Inch0.5451 Inch

H Gauge Height

N/A 0.0342 Inch0.0378 Inch

Min. Single Shear Strength1

N/A 7300 lb

Min. Tensile Strength1

N/A 5000 lb

K Lead-In Dia.

N/A 0.3029 Inch0.3055 Inch

M Ref.

N/A 0.230 Inch

BD Dia. Min. - Extended Grip6

N/A 0.391 Inch

BD Dia. Min. - Design Grip

N/A 0.406 Inch

Design Grip Range Min.

N/A 0.626 Inch

Design Grip Range Max.

N/A 0.687 Inch

L10

N/A 1.229 Inch

Material Sleeve

N/A A286 CRES

Material Core Bolt

N/A 6Al-4V Titanium per AMS 4967 or 4928

Finish Sleeve

N/A Passivate per AMS2700 Type 2 or Type 8

Finish Core Bolt

N/A Incotec Tec-Lube Dry Film Lube per AS5272 or Equivalent

Procurement Specification

N/A T0108

Complete Installation Tool

N/A ETT2026-10

Installation Nose Only

N/A ETT2000-10N

Recommended Installation Hole Sizes

N/A 0.313 Inch0.316 Inch

Installed Weight

N/A 21.20 Lbs/1000

N/A

Technical Specifications

  1. Single shear testing shall be in accordance with the requirements of NASM 1312-20 and applies to grips 05-05 min, 06-06 min, 08-07 min, 10-09 min and 12-10 min and longer. Tensile strength testing shall be in accordance with requirements of NASM 1312-8 and applies to grips 05-06 max, 06-07 max, 08-08 max, 10-10 max and 12-12 max and longer.
  2. Dimensions are in inches and are to be met after finish.
  3. 3 indentations 120° apart to provide thread lock.
  4. Blind side head may be installed on 5° maximum slope.
  5. The average smallest and largest observed values on the same specimen shall be equal to or greater than the stated minimum.
  6. Extended grip "BD min" value applies to a part driven .008"±.002" over the design maximum grip.
  7. Sleeve dia. may be up to .0003" oversize in band anneal zone. Zone extends from approximately blind end - .470" for the -05 Dia., - .525" for the -06 Dia.,- .635" for the -08 Dia., - .700" for the -10 Dia., and - .750" for the -12 Dia.
  8. Identification: -05 and -06: manufacturer's ID. -08, -10 and 12: manufacturer's ID and an optional circle or circle outline for ER213 head configuration. Marking indented .010 maximum, arrangement optional. -05 and -06 parts manufactured without manufacturer's ID may be used until stocks are depleted.
  9. Transition, optional radius or chamfer.
  10. Consult HFS for longer grip length availability.