close
close
close
Request Information

Blind Bolt Fastener, High Strength, Friction Thread Lock, Threaded, 100° Flush Tension Head, Titanium/A-286 (95 KSI Shear)

Unit of Measure

Nominal Diameter

 N/A 0.1900 Inch

Nominal Diameter No.

 N/A 06

A Theo Inter Ref.

 N/A 0.3813 Inch

J Max.

 N/A 0.015 Inch

C Driver Length Ref.

 N/A 0.250 Inch

D Shank Dia.

 N/A 0.1885 Inch0.1895 Inch

E Spline O.D. Ref.

 N/A 0.180 Inch

F Head Height Ref.

 N/A 0.081 Inch

R Radius Max.

 N/A 0.015 Inch

G Gauge Dia.

 N/A 0.3270 Inch0.3272 Inch

H Gauge Height

 N/A 0.0200 Inch0.0230 Inch

Min. Single Shear Strength1

 N/A 2690 lb

Min. Tensile Strength1

 N/A 1600 lb

K Lead-In Dia.

 N/A 0.1804 Inch0.1830 Inch

M Ref.

 N/A 0.065 Inch

BD Dia. Min. - Extended Grip6

 N/A 0.238 Inch

BD Dia. Min. - Design Grip

 N/A 0.247 Inch

Design Grip Range Min.

 N/A 0.751 Inch

Design Grip Range Max.

 N/A 0.812 Inch

L10

 N/A 1.169 Inch

Material Sleeve

 N/A A286 CRES

Material Core Bolt

 N/A 6Al-4V Titanium per AMS 4967 or 4928

Finish Sleeve

 N/A Passivate per AMS2700 Type 2 or Type 8

Finish Core Bolt

 N/A Incotec Tec-Lube Dry Film Lube per AS5272 or Equivalent

Procurement Specification

 N/A T0108

Complete Installation Tool

 N/A ETT2000-06

Installation Nose Only

 N/A ETT2000-06N

Recommended Installation Hole Sizes

 N/A 0.190 Inch0.193 Inch

Installed Weight

 N/A 7.07 Lbs/1000

N/A

Technical Specifications

  1. Single shear testing shall be in accordance with the requirements of NASM 1312-20 and applies to grips 05-05 min, 06-06 min, 08-07 min, 10-09 min and 12-10 min and longer. Tensile strength testing shall be in accordance with requirements of NASM 1312-8 and applies to grips 05-06 max, 06-07 max, 08-08 max, 10-10 max and 12-12 max and longer.
  2. Dimensions are in inches and are to be met after finish.
  3. 3 indentations 120° apart to provide thread lock.
  4. Blind side head may be installed on 5° maximum slope.
  5. The average smallest and largest observed values on the same specimen shall be equal to or greater than the stated minimum.
  6. Extended grip "BD min" value applies to a part driven .008"±.002" over the design maximum grip.
  7. Sleeve dia. may be up to .0003" oversize in band anneal zone. Zone extends from approximately blind end - .470" for the -05 Dia., - .525" for the -06 Dia.,- .635" for the -08 Dia., - .700" for the -10 Dia., and - .750" for the -12 Dia.
  8. Identification: -05 and -06: manufacturer's ID. -08, -10 and 12: manufacturer's ID and an optional circle or circle outline for ER213 head configuration. Marking indented .010 maximum, arrangement optional. -05 and -06 parts manufactured without manufacturer's ID may be used until stocks are depleted.
  9. Transition, optional radius or chamfer.
  10. Consult HFS for longer grip length availability.