close
close
close
Request Information

Blind Bolt Fastener, High Strength, Friction Thread Lock, Threaded, 100° Flush Tension Head, Titanium/A-286 (95 KSI Shear)

Unit of Measure

Nominal Diameter

 N/A 0.1640 Inch

Nominal Diameter No.

 N/A 05

A Theo Inter Ref.

 N/A 0.3304 Inch

J Max.

 N/A 0.010 Inch

C Driver Length Ref.

 N/A 0.250 Inch

D Shank Dia.

 N/A 0.1625 Inch0.1635 Inch

E Spline O.D. Ref.

 N/A 0.180 Inch

F Head Height Ref.

 N/A 0.070 Inch

R Radius Max.

 N/A 0.015 Inch

G Gauge Dia.

 N/A 0.2830 Inch0.2832 Inch

H Gauge Height

 N/A 0.0175 Inch0.0202 Inch

Min. Single Shear Strength1

 N/A 2005 lb

Min. Tensile Strength1

 N/A 1400 lb

K Lead-In Dia.

 N/A 0.1539 Inch0.1565 Inch

M Ref.

 N/A 0.060 Inch

BD Dia. Min. - Extended Grip6

 N/A 0.205 Inch

BD Dia. Min. - Design Grip

 N/A 0.213 Inch

Design Grip Range Min.

 N/A 0.313 Inch

Design Grip Range Max.

 N/A 0.375 Inch

L10

 N/A 0.701 Inch

Material Sleeve

 N/A A286 CRES

Material Core Bolt

 N/A 6Al-4V Titanium per AMS 4967 or 4928

Finish Sleeve

 N/A Aluminum Coat per NAS4006 with HI-KOTE1 or Equiv.

Finish Core Bolt

 N/A Incotec Tec-Lube Dry Film Lube per AS5272 or Equivalent

Procurement Specification

 N/A T0108

Complete Installation Tool

 N/A ETT2000-05

Installation Nose Only

 N/A ETT2000-05N

Recommended Installation Hole Sizes

 N/A 0.164 Inch0.167 Inch

Installed Weight

 N/A 3.23 Lbs/1000

N/A

Technical Specifications

  1. Single shear testing shall be in accordance with the requirements of NASM 1312-20 and applies to grips 05-05 min, 06-06 min, 08-07 min, 10-09 min and 12-10 min and longer. Tensile strength testing shall be in accordance with requirements of NASM 1312-8 and applies to grips 05-06 max, 06-07 max, 08-08 max, 10-10 max and 12-12 max and longer.
  2. Dimensions are in inches and are to be met after finish.
  3. 3 indentations 120° apart to provide thread lock.
  4. Blind side head may be installed on 5° maximum slope.
  5. The average smallest and largest observed values on the same specimen shall be equal to or greater than the stated minimum.
  6. Extended grip "BD min" value applies to a part driven .008"±.002" over the design maximum grip.
  7. Sleeve dia. may be up to .0003" oversize in band anneal zone. Zone extends from approximately blind end - .470" for the -05 Dia., - .525" for the -06 Dia.,- .635" for the -08 Dia., - .700" for the -10 Dia., and - .750" for the -12 Dia.
  8. Identification: -05 and -06: manufacturer's ID. -08, -10 and 12: manufacturer's ID and an optional circle or circle outline for ER213 head configuration. Marking indented .010 maximum, arrangement optional. -05 and -06 parts manufactured without manufacturer's ID may be used until stocks are depleted.
  9. Transition, optional radius or chamfer.
  10. Consult HFS for longer grip length availability.