close
close
Ti-Matic® Blind Bolt Fastener, High Strength, Pull-Type, Positive Mechanical Lock, 130° Flush Head
Unit of Measure

Nominal Diameter

N/A 08

A Head Theo. Inter.

N/A 0.507 in

A Min.

N/A 0.434086764702675 in

Amin

N/A 0.463 in

B Head Height

N/A 0.057 in

C Min

N/A 1.000 in

D

N/A 0.259 in

E Max

N/A 0.305 in

F Land THK Max

N/A 0.017 in

G Gage

N/A 0.4319 in

H Gage Height

N/A 0.0198-0.0237

R Rad Max

N/A 0.030 in

S Design Ref Only

N/A 0.361 in

Design Grip Range Min. - Max.

N/A 0.281 - 0.345

Single Shear Strength

N/A 5005 lb

Tensile Strength

N/A 2100 lb

Hole Limits

N/A 0.260 in

Grip Dash No.

N/A 05

Overlap Grip Max

N/A 0.361 in

Design Grip Range Min.

N/A 0.281 in

Design Grip Range Max.

N/A 0.345 in

Finish Code

N/A AC

Sleeve Material

N/A CP titanium per chemistry of ASTM B348 Grade 1

Pin Material

N/A 38-6-44 titanium per chemistry of AMS4957 or AMS-T-9047

Lock Collar Material

N/A A-286 per chemistry of AMS5737 or type 316 cres per chemistry of AMS5690

Sleeve Finish

N/A Aluminum coat per NAS4006

Pin Finish

N/A None

Lock Collar Finish

N/A Passivate per AMS2700 and AMS-QQ-P-35

Sleeve Lube

N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1

Pin Lube

N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1

Lock Collar Lube

N/A Dicronite DL-5 lube per DOD-L-85645

Notes

N/A 1. Diameter "D" may be .0005" oversize for coated parts.
2. Applies to grips 05-04 Max, 06-05 Max and greater. In shorter grips, a true composite shear test cannot be performed.
3. Solid or split lock collar at manufacturer´s option. Split not to exceed .020 width.
4. Trim flash not to exceed .005 maximum length above head of pin.
5. Knurled to retain fastener assembly. Not part of installed fastener.
6. Blind side head may be installed on 7° max slope.
7. Identification: Huck symbol, MV (for CP titanium sleeve material) and grip dash number.
8. The average reading of the smallest & largest observed value on the same specimen must be equal to or greater than the stated minimum diameter. This is applicable to design grip range.
9. Concentracity: Conical surface of flush head to "D" diameter to be within .010 F.I.M.
10. Optional drive washer for installation with blunt tool. Not part of installed fastener.
11. Sleeve diameter "D" may be .001" undersize in this area.
12. Overlap in design grip range makes fastener well-suited for composite structures with large grip tollerances. Fastener is intended to be installed to be installed in "design grip range". Fasteners installed in grips above "design grip range" perform reliably provided that the installed pin and collar flushness requirements are met.
13. Dimensions "A", "A´" & "B" are for engineering reference only and are not for inspection purposes. They are calculated limits resulting from tolerances on "G", "H", "D", "F" and head angle.
14. UB130-MV06-02 grip range is .120-.157.
15. Lube and lock collar material at manufacturer´s option.