HowmetHowmet
Nominal Diameter |
N/A 06 |
A Head Theo. Inter. |
N/A 0.386 in |
A Min. |
N/A 0.330242820066751 in |
Amin |
N/A 0.347 in |
B Head Height |
N/A 0.043 in |
C Min |
N/A 0.875 in |
D |
N/A 0.198 in |
E Max |
N/A 0.250 in |
F Land THK Max |
N/A 0.013 in |
G Gage |
N/A 0.3271 in |
H Gage Height |
N/A 0.0162-0.0192 |
R Rad Max |
N/A 0.025 in |
S Design Ref Only |
N/A 0.292 in |
Design Grip Range Min. - Max. |
N/A 0.781 - 0.845 |
Single Shear Strength |
N/A 2925 lb |
Tensile Strength |
N/A 1400 lb |
Hole Limits |
N/A 0.199 in |
Grip Dash No. |
N/A 13 |
Overlap Grip Max |
N/A 0.861 in |
Design Grip Range Min. |
N/A 0.781 in |
Design Grip Range Max. |
N/A 0.845 in |
Finish Code |
N/A AC |
Sleeve Material |
N/A CP titanium per chemistry of ASTM B348 Grade 1 |
Pin Material |
N/A 38-6-44 titanium per chemistry of AMS4957 or AMS-T-9047 |
Lock Collar Material |
N/A A-286 per chemistry of AMS5737 or type 316 cres per chemistry of AMS5690 |
Sleeve Finish |
N/A Aluminum coat per NAS4006 |
Pin Finish |
N/A None |
Lock Collar Finish |
N/A Passivate per AMS2700 and AMS-QQ-P-35 |
Sleeve Lube |
N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1 |
Pin Lube |
N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1 |
Lock Collar Lube |
N/A Dicronite DL-5 lube per DOD-L-85645 |
Notes |
N/A
1. Diameter "D" may be .0005" oversize for coated parts. 2. Applies to grips 05-04 Max, 06-05 Max and greater. In shorter grips, a true composite shear test cannot be performed. 3. Solid or split lock collar at manufacturer´s option. Split not to exceed .020 width. 4. Trim flash not to exceed .005 maximum length above head of pin. 5. Knurled to retain fastener assembly. Not part of installed fastener. 6. Blind side head may be installed on 7° max slope. 7. Identification: Huck symbol, MV (for CP titanium sleeve material) and grip dash number. 8. The average reading of the smallest & largest observed value on the same specimen must be equal to or greater than the stated minimum diameter. This is applicable to design grip range. 9. Concentracity: Conical surface of flush head to "D" diameter to be within .010 F.I.M. 10. Optional drive washer for installation with blunt tool. Not part of installed fastener. 11. Sleeve diameter "D" may be .001" undersize in this area. 12. Overlap in design grip range makes fastener well-suited for composite structures with large grip tollerances. Fastener is intended to be installed to be installed in "design grip range". Fasteners installed in grips above "design grip range" perform reliably provided that the installed pin and collar flushness requirements are met. 13. Dimensions "A", "A´" & "B" are for engineering reference only and are not for inspection purposes. They are calculated limits resulting from tolerances on "G", "H", "D", "F" and head angle. 14. UB130-MV06-02 grip range is .120-.157. 15. Lube and lock collar material at manufacturer´s option. |
