HowmetHowmet
Nominal Diameter |
N/A 06 |
Design Grip Range Min. - Max. |
N/A 0.469 - 0.532 |
A Head Theo. Max |
N/A 0.386 in |
B Head Height |
N/A 0.080 in |
C Min |
N/A 0.875 in |
D |
N/A 0.198 in |
E Max |
N/A 0.250 in |
F Max |
N/A 0.013 in |
G Gage |
N/A 0.3271 in |
H Gage Height |
N/A 0.0205-0.0243 |
R Rad Max |
N/A 0.015 in |
S Design Ref Only |
N/A 0.292 in |
Z Min |
N/A 0.275 in |
Single Shear Strength |
N/A 2925 lb |
Tensile Strength |
N/A 1400 lb |
Hole Diameter |
N/A 0.199 in |
Grip Dash No. |
N/A 08 |
Overlap Grip Max |
N/A 0.548 in |
Design Grip Range Min. |
N/A 0.469 in |
Design Grip Range Max. |
N/A 0.532 in |
Finish Code |
N/A None |
Sleeve Material |
N/A CP titanium per chemistry of ASTM B348 Grade 1 |
Pin Material |
N/A 38-6-44 titanium per chemistry of SAE-AMS4957 or SAE-AMS-T-9047 |
Lock Collar Material |
N/A A-286 per chemistry of SAE-AMS5737 or TYPE 316 cres per chemistry of SAE-AMS5690 |
Sleeve Finish |
N/A None |
Pin Finish |
N/A None |
Lock Collar Finish |
N/A Passivate per SAE-AMS2700 Type 2 or Type 8 |
Sleeve Lube |
N/A None or cetyl alcohol per SAE-AS87132 or dry film lube per SAE-AS5272 Type 1 |
Pin Lube |
N/A None or cetyl alcohol per SAE-AS87132 or dry film lube per SAE-AS5272 Type 1 |
Lock Collar Lube |
N/A Dicronite DL-5 lube per DOD-L-85645 |
Notes |
N/A
1. Diameter "D" may be .0005" oversize for coated parts. 2. Applies to grips 04-03 Max, 06-05 Max, 08-06 Max, and 10-07 Max and greater. In shorter grips, a true composite shear test cannot be performed. 3. Trim flash not to exceed .005 maximum length above head of pin. 4. Solid or split lock collar at manufacturer´s option. Split not to exceed .020 width. 5. Dimensions "A" and "B" are for reference only. They are calculated limits resulting from tolerances on "H", "G", "D", "F" and head angle. 6. Blind side head may be installed on 7° max slope. 7. Identification: Huck symbol, MV (for CP titanium sleeve material) and grip dash number. 8. The average reading of the smallest & largest observed value on the same specimen must be equal to or greater than the stated minimum diameter. This is applicable to design grip range. 9. Concentricity: Conical surface of flush head to "D" diameter to be within .010 F.I.M. 10. Optional drive washer for installation with blunt tool. Not part of installed fastener. 11. Sleeve diameter "D" may be .001" undersize in this area. 12. Overlap in design grip range makes fastener well-suited for composite structures with large grip tolerances fastener is intended to be installed in "design grip range". Fasteners installed in grips above "design grip range" perform reliably provided that the installed pin and collar flushness requirements are met. 13. Knurled to retain fastener assembly. Not part of installed fastener. 14. Grip range for 06-02 IS .120 to .157. 15. Lube and lock collar material at manufacturer´s option. |
