Howmet
Nominal Diameter |
N/A 04 |
Design Grip Range Min. - Max. |
N/A 0.281 - 0.345 |
A Head Theo. Max |
N/A 0.229 in |
B Head Height |
N/A 0.042 in |
C Min |
N/A 0.812 in |
D |
N/A 0.128 in |
E Max |
N/A 0.190 in |
F Max |
N/A 0.009 in |
G Gage |
N/A 0.1840 in |
H Gage Height |
N/A 0.0155-0.0185 |
R Rad Max |
N/A 0.010 in |
S Design Ref Only |
N/A 0.172 in |
Z Min |
N/A 0.185 in |
Single Shear Strength |
N/A 1222 lb |
Tensile Strength |
N/A 600 lb |
Hole Diameter |
N/A 0.129 in |
Grip Dash No. |
N/A 05 |
Overlap Grip Max |
N/A 0.361 in |
Design Grip Range Min. |
N/A 0.281 in |
Design Grip Range Max. |
N/A 0.345 in |
Finish Code |
N/A AT |
Sleeve Material |
N/A CP titanium per chemistry of ASTM B348 Grade 1 |
Pin Material |
N/A 38-6-44 titanium per chemistry of SAE-AMS4957 or SAE-AMS-T-9047 |
Lock Collar Material |
N/A A-286 per chemistry of SAE-AMS5737 or TYPE 316 cres per chemistry of SAE-AMS5690 |
Sleeve Finish |
N/A Blue anodize per ISO 8080 |
Pin Finish |
N/A None |
Lock Collar Finish |
N/A Passivate per SAE-AMS2700 Type 2 or Type 8 |
Sleeve Lube |
N/A None or cetyl alcohol per SAE-AS87132 |
Pin Lube |
N/A None or cetyl alcohol per SAE-AS87132 |
Lock Collar Lube |
N/A Dicronite DL-5 lube per DOD-L-85645 |
Notes |
N/A
1. Diameter "D" may be .0005" oversize for coated parts. 2. Applies to grips 04-03 Max, 06-05 Max, 08-06 Max, and 10-07 Max and greater. In shorter grips, a true composite shear test cannot be performed. 3. Trim flash not to exceed .005 maximum length above head of pin. 4. Solid or split lock collar at manufacturer´s option. Split not to exceed .020 width. 5. Dimensions "A" and "B" are for reference only. They are calculated limits resulting from tolerances on "H", "G", "D", "F" and head angle. 6. Blind side head may be installed on 7° max slope. 7. Identification: Huck symbol, MV (for CP titanium sleeve material) and grip dash number. 8. The average reading of the smallest & largest observed value on the same specimen must be equal to or greater than the stated minimum diameter. This is applicable to design grip range. 9. Concentricity: Conical surface of flush head to "D" diameter to be within .010 F.I.M. 10. Optional drive washer for installation with blunt tool. Not part of installed fastener. 11. Sleeve diameter "D" may be .001" undersize in this area. 12. Overlap in design grip range makes fastener well-suited for composite structures with large grip tolerances fastener is intended to be installed in "design grip range". Fasteners installed in grips above "design grip range" perform reliably provided that the installed pin and collar flushness requirements are met. 13. Knurled to retain fastener assembly. Not part of installed fastener. 14. Grip range for 06-02 IS .120 to .157. 15. Lube and lock collar material at manufacturer´s option. |
