close
close
Ti-Matic, Blind Bolt Fastener, High Strength, Pull-Type, Positive Mechanical Lock, 100° Flush Head, Aluminum coated
Unit of Measure

Nominal Diameter

N/A 08

Design Grip Range Min. - Max.

N/A 0.594 - 0.657

A Head Theo. Inter. Max

N/A 0.507 in

(B) Head Height

N/A 0.105 in

C Min

N/A 1.000 in

D

N/A 0.259 in

E Max

N/A 0.305 in

F Max

N/A 0.017 in

G Gage

N/A 0.4319 in

H Gage Height

N/A 0.0270-0.0310

R Rad Max

N/A 0.020 in

(S) Design Ref Only

N/A 0.361 in

Z Min

N/A 0.325 in

Single Shear Strength

N/A 5005 lb

Tensile Strength

N/A 2900 lb

Hole Diameter

N/A 0.260 in

Grip Dash No.

N/A 10

Overlap Grip Max

N/A 0.673 in

Design Grip Range Min.

N/A 0.594 in

Design Grip Range Max.

N/A 0.657 in

Finish Code

N/A AC

Sleeve Material

N/A A-286 per chemistry of AMS5737

Pin Material

N/A 38-6-44 titanium per chemistry of AMS4957 or AMS-T-9047

Lock Collar Material

N/A A-286 per chemistry of AMS5737 or type 316 cres per chemistry of AMS5690

Sleeve Finish

N/A Aluminum coat per NAS4006

Pin Finish

N/A None

Lock Collar Finish

N/A Passivate per AMS2700

Sleeve Lube

N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1

Pin Lube

N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1

Lock Collar Lube

N/A Dicronite DL-5 lube per DOD-L-85645

N/A 1. Minimum ultimate single shear and tensile strength, in pounds, of installed fastener.
2. Applies to grips 05-04 max, 06-05 max, 08-06 max, 10-07 max and greater. In shorter grips a true composite shear test cannot be obtained.
3. Trim flash not to exceed .005 maximum length above head of pin.
4. Solid or split lock collar at manufacturer´s option. Split not to exceed .020.
5. Knurled to retain fastener components. Not part of installed fastener.
6. Blind side head may be installed on 5° max slope.
7. Identification: Huck symbol, "EV", and grip dash number.
8. The average reading of the smallest & largest observed value on the same specimen must be equal to or greater than the stated minimum diameter. This is applicable to design grip range.
9. Concentricity: Conical surface of flush head to "D" diameter to be within .010 F.I.M.
10. Optional drive washer for installation with blunt nosed tool. Not part of installed fastener.
11. "E" length of diameter "D" may be .002 undersized.
12. Diameter of pin head shall not exceed "D" may and may be .002 below "D" min.
13. Overlap in design grip range makes fastener well-suited for composite structures with large grip tolerances. Fastener is intended to be installed in "design grip range". Fasteners installed in grips above "design grip range" perform reliably provided that the installed pin and collar flushness requirements are met.
14. The grip range of UB100-EV06-02 in .120 to .157.
15. Diameter "D" may be .0005" oversize for coated parts.
16. Lube and lock collar material at manufacturer´s option.