Item # UB100-EV05-08, UB100-EV On Howmet Aerospace

Request Information

Ti-Matic, Blind Bolt Fastener, High Strength, Pull-Type, Positive Mechanical Lock, 100° Flush Head

Unit of Measure

Specifications
Notes

Nominal Diameter	N/A 05
Design Grip Range Min. - Max.	N/A 0.469 - 0.532
A Head Theo. Inter. Max	N/A 0.333 in
(B) Head Height	N/A 0.072 in
C Min	N/A 0.844 in
D	N/A 0.163 in
E Max	N/A 0.220 in
F Max	N/A 0.011 in
G Gage	N/A 0.2831 in
H Gage Height	N/A 0.0171-0.0206
R Rad Max	N/A 0.010 in
(S) Design Ref Only	N/A 0.232 in
Z Min	N/A 0.205 in
Single Shear Strength	N/A 1980 lb
Tensile Strength	N/A 1150 lb
Hole Diameter	N/A 0.164 in
Grip Dash No.	N/A 08
Overlap Grip Max	N/A 0.548 in
Design Grip Range Min.	N/A 0.469 in
Design Grip Range Max.	N/A 0.532 in
Finish Code	N/A None
Sleeve Material	N/A A-286 per chemistry of AMS5737
Pin Material	N/A 38-6-44 titanium per chemistry of AMS4957 or AMS-T-9047
Lock Collar Material	N/A A-286 per chemistry of AMS5737 or type 316 cres per chemistry of AMS5690
Sleeve Finish	N/A Passivate per AMS2700
Pin Finish	N/A None
Lock Collar Finish	N/A Passivate per AMS2700
Sleeve Lube	N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1
Pin Lube	N/A None or cetyl alcohol per AS87132 or dry film lube per AS5272 Type 1
Lock Collar Lube	N/A Dicronite DL-5 lube per DOD-L-85645

N/A 1. Minimum ultimate single shear and tensile strength, in pounds, of installed fastener.
2. Applies to grips 05-04 max, 06-05 max, 08-06 max, 10-07 max and greater. In shorter grips a true composite shear test cannot be obtained.
3. Trim flash not to exceed .005 maximum length above head of pin.
4. Solid or split lock collar at manufacturer´s option. Split not to exceed .020.
5. Knurled to retain fastener components. Not part of installed fastener.
6. Blind side head may be installed on 5° max slope.
7. Identification: Huck symbol, "EV", and grip dash number.
8. The average reading of the smallest & largest observed value on the same specimen must be equal to or greater than the stated minimum diameter. This is applicable to design grip range.
9. Concentricity: Conical surface of flush head to "D" diameter to be within .010 F.I.M.
10. Optional drive washer for installation with blunt nosed tool. Not part of installed fastener.
11. "E" length of diameter "D" may be .002 undersized.
12. Diameter of pin head shall not exceed "D" may and may be .002 below "D" min.
13. Overlap in design grip range makes fastener well-suited for composite structures with large grip tolerances. Fastener is intended to be installed in "design grip range". Fasteners installed in grips above "design grip range" perform reliably provided that the installed pin and collar flushness requirements are met.
14. The grip range of UB100-EV06-02 in .120 to .157.
15. Diameter "D" may be .0005" oversize for coated parts.
16. Lube and lock collar material at manufacturer´s option.

Email ^*
First Name ^*
Last Name ^*
Company ^*
Country ^*
Zip/Postal Code ^*

Nominal Diameter

Design Grip Range Min. - Max.

A Head Theo. Inter. Max

(B) Head Height

C Min

D

E Max

F Max

G Gage

H Gage Height

R Rad Max

(S) Design Ref Only

Z Min

Single Shear Strength

Tensile Strength

Hole Diameter

Grip Dash No.

Overlap Grip Max

Design Grip Range Min.

Design Grip Range Max.

Finish Code

Sleeve Material

Pin Material

Lock Collar Material

Sleeve Finish

Pin Finish

Lock Collar Finish

Sleeve Lube

Pin Lube

Lock Collar Lube