close
close
UniMatic® Blind Bolt Fastener, High Strength, Pull-Type, Positive Mechanical Lock, 100° Flush Head, Large Footprint
Unit of Measure

Nominal Diameter

N/A 08

Design Grip Range Min. - Max.

N/A 0.594 - 0.657

A Head Theo. Inter Ref

N/A 0.507 in

B Head Height Ref

N/A 0.105 in

C Min

N/A 1.000 in

D

N/A 0.259 in

E Max

N/A 0.370 in

F Max

N/A 0.017 in

G Gage

N/A 0.4319 in

H Gage Height

N/A 0.0270-0.0310

J

N/A 0.375 in

K

N/A 0.975

N

N/A 0.190 in

R Rad Max

N/A 0.020 in

S Design Ref Only

N/A 0.361 in

W Min

N/A 0.363 in

Single Shear Strength

N/A 5000 lb

Tensile Strength

N/A 2100 lb

Grip Dash No.

N/A 10

Overlap Grip Min

N/A 0.578 in

Overlap Grip Max

N/A 0.673 in

Finish Code

N/A DF

Installed Weight

N/A 9.28 lb

Sleeve Material

N/A CP titanium per ASTM-B348

Pin Material

N/A 38-6-44 titanium per AMS4957

Lock Collar Material

N/A A-286 cres per AMS5737

Sleeve Finish

N/A None

Pin Finish

N/A None

Lock Collar Finish

N/A Passivate per AMS QQ-P-35 and AMS2700

Sleeve Lube

N/A Lubed shall use AS5272 on any of the fastener components except mechanical lock may use lox compatible dry film lube (MFG's option)

Pin Lube

N/A Luber shall use AS5272 on any of the fastener components except mechanical lock may use lox compatible dry film lube (MFG's option)

Lock Collar Lube

N/A Lubed shall use AS5272 on any of the fastener components except mechanical lock may use lox compatible dry film lube (MFG's option)

N/A 1. -05 Dia size also available with reduced O.D. drive anvil of .312+.005 (see sheet 3)
2. Applies to grips 05-04 Max, 06-05 Max, 08-06 Max and greater. In shorter grips, a true composite shear test cannot be performed.
3. Trim flash not to exceed .005" maximum length above head of pin.
4. Solid or split lock collar at manufacturer´s option. Split not to exceed .020 width.
5. Knurled to retain fastener assembly. Not part of installed fastener.
6. Blind side head may be installed on 7° max slope.
7. Identification: Huck symbol, MV (for CP titanium sleeve material) and grip dash number.
8. Optional drive washer for installation with blunt tool. Not part of installed fastener.
9. Sleeve diameter "D" may be .002" undersized in this area.
10. Overlap minimum grip for -06 diameter is .140, for -08 diameter is none.
11. Lube and lock collar material at manufacturer´s option.
12. Lubrication: Serrated pin: None or cetyl alcohol (chlorine free) per AS87132 type 1 or dry film lube per AS5272 at manufacture´s option.
Mechanical lock: None or lox compatible dry film lube at manufacturer´s option.
Sleeve: NO suffix and AC suffix: None or cetyl alcohol (chlorine free) per AS87132 Type 1 or dry film lube per AS5272 at manufacturer´s option.
13. DF suffix parts when lubed shall use AS5272 on any of the fastener components except mechanical lock may use lox compatible dry film lube (MFG´S option).