close
close
Unimatic® Blind Bolt Fastener, High Strength, Pull-Type, Positive Mechanical Lock, 100° Flush Head, Alloy Steel (112 KSI Shear) Single Action Installation
Unit of Measure

Nominal Diameter

N/A 8

A Head Theo Inter Max.

N/A 0.507 in

B Head Height Max.

N/A 0.105 in

C Min.

N/A 1.000 in

D Sleeve Dia. ± .001

N/A 0.259 in

E Max.

N/A 0.305 in

F Max.

N/A 0.017 in

G Gage Dia. ± .0001

N/A 0.432 in

H Gage Height

N/A 0.027 in0.031 in

R Rad. Max.

N/A 0.020 in

S Design Ref. Only Max.

N/A 0.279 in

Single Shear1,2

N/A 5900 lb

Tensile1

N/A 3650 lb

Hole Limits +.003 / -.000

N/A 0.260 in

Grip Dash No.

N/A 15

Design Grip Range Min.

N/A 0.906 in

Design Grip Range Max.

N/A 0.970 in

L Ref.

N/A 1.156 in

M Max.

N/A 1.366 in

MS part number

N/A MS90353U0815

Material Sleeve

N/A Alloy Steel

Material Pin

N/A 8740 Alloy Steel per ASTM-A-331, ASTM-A-29, or AMS6322

Material Mechanical Lock

N/A A286 CRES per Chemistry of AMS5737 or 316 CRES for Chemistry of AMS5690 (Manufacturer's Option)

Protective Treatment Sleeve

N/A Cadmium Plate per QQ-P-416, Type II, Class 2 or Aluminum Coating per MIL-C-83488

Protective Treatment Pin

N/A Cadmium Plate per QQ-P-416, Type I, Class 3 with Hydrogen Embrittlement Relief per MIL-F-81177 or Aluminum Coating per MIL-C-83488

Lubrication Pin & Sleeve

N/A None

Lubrication Mechanical Lock

N/A Passivate per QQ-P-35, A-286 Cres and 316 Cres Only. Lubrication None or Manufacturer's Option to Lubricate Mechanical Lock only with Lox Compatible Dry Film.

N/A

  1. Minimum ultimate single shear and tensile strengths, in pounds, of installed fastener.
  2. Applies to grips 05-05. 06-05. 08-07. 10-08. 12-10 and up.In shorter grips a true composite shear test cannot be obtained.
  3. Trim flash not to exceed .005 maximum length above head of pin.
  4. Solid or split lock collar - Manufacturer's option. Split not to exceed .020 width.
  5. Knurled to facilitate fastener assembly. Not part of installed fastener.
  6. Maximum diameter of blind head shall not exceed maximum diameter ofmanufactured head "A". For engineering design ref. only.
  7. Blind side head may be installed on 5° maximum slope.
  8. Nominal size 05 and 06 part numbers shown are color identified green (location optional).
  9. Identification: Manufacturer's option - Huck symbol, and grip dash number. Single digit marking is permissible for grip numbers less than 10.
  10. Concentricity: Conical surface of flush head to "D" diameter to be within .010 T.I.R...
  11. Diameter of pin head shall not exceed "D" max. and may be .002 below "D" min.
  12. Drive washer available to facilitate installation only. Not part of installed fastener.
  13. The grip range of UB100-T06-02 is .120 to .157.