HowmetHowmet
Dash Number (Grip) |
N/A -150 |
Grip Range - Min. Grip |
N/A 0.512 in |
Grip Range - Max. Grip |
N/A 0.591 in |
Grip Range |
N/A 0.512-0.591 in |
Nominal Dia |
N/A 0.157 in |
A Dia Max |
N/A 0.315 in |
B Dia Min |
N/A 0.283 in |
D Dia |
N/A 0.157 in |
E Dia Max |
N/A 0.157 in |
F Wrench Flats |
N/A 0.081 in |
G Ref. |
N/A 0.020 in |
H Ref. |
N/A 0.067 in |
L Ref. |
N/A 0.570 in |
R Rad |
N/A 0.016 in |
S Max |
N/A 0.015 in |
T Across Hex Ref. |
N/A 0.375 in |
V Gage Prot. |
N/A 0.025 in |
W Gage Dia |
N/A 0.256 in |
Recommended Hole Size |
N/A 0.1575-0.1604 |
J Dia Min |
N/A 0.240 in |
K Max |
N/A 0.370 in |
Break off Limits <4> |
N/A 0.050-0.053 |
Tensile Structural Failure (Min) |
N/A 854 lb |
Double Shear Min |
N/A 2960 lb |
Prevailing Torque Min |
N/A 1.000 lb-in0.110 N-m |
Material and Heat Treat |
N/A
Nut: 6AL-4V titanium per AMS 4928 or AMS 4967; Heat treated per MIL-H81200 to 95 ksi shear strength minimum, maximum hydrogen 125 ppm Corebolt: A-286 per AMS 5731, AMS 5732 or AMS 5737; heat treated to 175 ksi tensile min. Sleeve: 304 stainless steel per AMS 5639; heat treated as required for performance. Insert: Acetal per ASTM D4181 DryvcapTM: Mild steel. |
Finish |
N/A
(-) Nut: KAL-GARD ANN-RO #1012 conversion coating or phosphate flouride per AMS 2486 may be used at manufacturer´s option. Sleeve & Corebolt: Passivate per AMS-QQ-P-35. KAL-GARD ANN-RO #1013 conversion coating optional. Insert: None Dryvcap |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol. |
Applicable Specification |
N/A
Procurement specification: FCBF208 Special lube and finish: FCBF202 |
Material Type |
N/A Titanium |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A 100° Flush |
Notes |
N/A
2.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D. 3.Composite blind fastener with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufacturer´s option. Contact Fairchild Engineering. <4> An "L" in place of the dash (-) between the diameter the diameter dash number and the grip dash number designates modified break-off limits of +.053/-.050. "EX: FCBF7012-6L200". <5> Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to a minimum recommended hole size. Insertion force shall not not exceed 5.0 lbs (22.24 Newtons). |
