HowmetHowmet
Dash Number (Grip) |
N/A 1000 |
Grip Range - Min. Grip |
N/A 0.950 in |
Grip Range - Max. Grip |
N/A 1.000 in |
Grip Range |
N/A 0.950-1.000 in |
A Dia Ref. |
N/A 0.332 in |
B Dia Min |
N/A 0.296 in |
D Dia |
N/A 0.165 in |
E Dia Max |
N/A 0.164 in |
F Wrench Flats |
N/A 0.085 in |
G Ref. |
N/A 0.058 in |
H Ref. |
N/A 0.070 in |
L Ref. |
N/A 0.625 in |
R Rad Max |
N/A 0.030 in |
S Max |
N/A 0.015 in |
T Across Hex. Ref |
N/A 0.375 in |
Minimum available grip length |
N/A -150 |
Recommended Hole Size |
N/A 0.165-0.168 |
J Dia Min |
N/A 0.250 in |
K Max |
N/A 0.370 in |
Break off Limits <5> |
N/A 0.000-0.103 |
Tensile Structural Failure (Min) |
N/A 900 lb |
Double Shear Min |
N/A 3150 lb |
Locking Torque Min |
N/A 1.000 lb-in0.113 N-m |
V Gage Prot. |
N/A 0.021 in |
W Gage Dia |
N/A 0.283 in |
Material and Heat Treat |
N/A
Nut: A-286 stainless steel per chemical requirements of AMS 5732; heat treated as required for performance. Corebolt: A-286 per AMS 5731, AMS 5732 or AMS 5737; Heat treated to 175 ksi tensile min. Sleeve: 304 stainless steel per AMS 5639; heat treated as required for performance. Insert: Acetal per ASTM D4181 DryvcapTM: Mild steel. |
Finish |
N/A
Nut, Sleeve & Corebolt: Passivate per AMS-QQ-P-35. KAL-GARD ANN-RO #1013 conversion coating optional. Insert: None DryvcapTM: Color brown. |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol per MIL-L-87132. |
Applicable Specification |
N/A
Procurement specification: FCBF208 Special lube and finish: FCBF202 |
Material Type |
N/A A286 CRES |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A 100° Flush |
Notes |
N/A
2.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D. 3.Composite blind fastener with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufacturer´s option. Contact Fairchild Engineering. 4. These parts are similar to FCBF2122 except as follows: A. Improved out-of-grip flagging capacity (corebolt B/O) B. Increased blind side protrusion before and after upset C. Increased installed weight <5> An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates modified break-off limits of +.053/-.050. "EX: FCBF3010( )-6L200". <6>Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to minimum recommended hole size. Insertion force shall not exceed 5.0 lbs. |
