HowmetHowmet
Dash Number (Grip) |
N/A 650 |
Grip Range - Min. Grip |
N/A 0.600 in |
Grip Range - Max. Grip |
N/A 0.650 in |
Grip Range |
N/A 0.600-0.650 in |
A Dia |
N/A 0.541 in |
D Dia |
N/A 0.260 in |
E Dia Max |
N/A 0.260 in |
F Wrench Flats |
N/A 0.135 in |
G Ref. |
N/A 0.058 in |
H |
N/A 0.085 in |
L Ref. |
N/A 0.900 in |
R Rad Max |
N/A 0.030 in |
T Across Hex. Ref. |
N/A 0.375 in |
Z Max |
N/A 0.040 in |
Minimum available grip length |
N/A -150 |
Recommended Hole Size |
N/A 0.260-0.263 |
J Dia Min |
N/A 0.400 in |
K Max |
N/A 0.510 in |
Break off Limits <5> |
N/A 0.050-0.053 |
Tensile Structural Failure (Min) |
N/A 2100 lb |
Double Shear Min |
N/A 7900 lb |
Locking Torque Min |
N/A 2.500 lb-in0.282 N-m |
P_CAD |
N/A 1.100 in |
Material and Heat Treat |
N/A
Nut: A-286 stainless steel per chemical requirements of AMS 5732; heat treated as required for performance. Corebolt: A-286 per AMS 5731, AMS 5732 or AMS 5737; Heat treated to 175 ksi tensile min. Sleeve: 304 stainless steel per AMS 5639; heat treated as required for performance. Insert: Acetal per ASTM D4181 DryvcapTM: Mild steel. |
Finish |
N/A
Nut, Sleeve & Corebolt: Passivate per AMS-QQ-P-35. KAL-GARD ANN-RO #1013 conversion coating optional. Insert: None DryvcapTM: Color brown. |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol per MIL-L-87132. |
Applicable Specification |
N/A
Procurement specification: FCBF208 Special lube and finish: FCBF202 |
Material Type |
N/A A286 CRES |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A Protruding |
Notes |
N/A
2.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D. 3.Composite blind fastener with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufacturer´s option. Contact Fairchild Engineering. 4. These parts are similar to FCBF2120 except as follows: A. Improved out-of-grip flagging capacity (corebolt B/O) B. Increased blind side protrusion before and after upset C. Increased installed weight <5> An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates modified break-off +.053/-.050. "EX: FCBF3008( )-6L200". <6>Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to minimum recommended hole size. Insertion force shall not exceed 5.0 lbs. |
