Howmet
Dash Number (Grip) |
N/A 100 |
Grip Range - Min. Grip |
N/A 0.050 in |
Grip Range - Max. Grip |
N/A 0.100 in |
Grip Range |
N/A 0.050-0.100 in |
A Theo. Dia |
N/A 0.261 in |
B Dia Min |
N/A 0.241 in |
D Dia |
N/A 0.167 in |
E Dia Max |
N/A 0.164 in |
F Wrench Flats |
N/A 0.085 in |
G Ref. |
N/A 0.017 in |
H Ref. |
N/A 0.040 in |
L Ref. |
N/A 0.512 in |
R Rad Max |
N/A 0.030 in |
S Max |
N/A 0.009 in |
T Across Hex. Ref |
N/A 0.375 in |
Minimum available grip length |
N/A -150 |
Recommended Hole Size |
N/A 0.165-0.166 |
J Dia Min |
N/A 0.250 in |
K Max |
N/A 0.300 in |
Break off Limits <5> |
N/A 0.100-0.003 |
Tensile Structural Failure (Min) <7> |
N/A 1400 lb |
Double Shear Min |
N/A 4150 lb |
Locking Torque Min |
N/A 1.000 lb-in0.113 N-m |
V Gage Prot. |
N/A 0.027 in |
W Gage Dia |
N/A 0.199 in |
Material and Heat Treat |
N/A
Nut: A-286 stainless steel per chemical requirements of AMS 5732, heat treated as required for performance. Corebolt: Inconel 718 per AMS 5662, heat treated to 125 ksi Fsu Sleeve: 304 stainless steel per AMS 5639, heat treated as required for performance. Insert: Acetal per ASTM D4181 DryvcapTM: Mild steel. |
Finish |
N/A
Nut, Sleeve & Corebolt: Passivate per AMS-QQ-P-35. KAL-GARD ANN-RO #1013 conversion coating optional. Insert: None DryvcapTM: Corrosion resistant coating, color black. |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol per MIL-L-87132. |
Applicable Specification |
N/A
Procurement specification: FCBF200 Special lube and finish: FCBF202 |
Material Type |
N/A A286 CRES |
Rated Shear Strength |
N/A 90 KSI |
Headstyle |
N/A 100° Flush |
Notes |
N/A
2.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D. <3>Alternate head marking: "VS" and "O" 4.Composite blind fasteners with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufacrure´s option. Contact Fairchild Engineering. <5>An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates midified break-off limits of +.053/-.050. (e.g. FCBF2134( )-6L200). An "LL" designates modified break-off limits of +.003/-.100 "e.g. FCBF2134( )-6LL200". <6>Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to minimum recommended hole. Insertion force shall not exceed 5.0 lbs. <7> Proposed minimum tensile structural failure values. 8. These parts are intended for applications requiring up to a .002" diametral interference fit between fastener shank and structure hole. |
