close
close
ACCU-LOK® II blind fastener for composite application low profile protruding head A-286 CRES.
Unit of Measure

Dash Number (Grip)

N/A 900

Grip Range - Min. Grip

N/A 0.850 in

Grip Range - Max. Grip

N/A 0.900 in

Grip Range

N/A 0.850-0.900 in

A Dia

N/A 0.765 in

D Dia

N/A 0.375 in

E Dia Max

N/A 0.374 in

F Wrench Flats

N/A 0.185 in

G Ref.

N/A 0.080 in

H

N/A 0.125 in

L Ref.

N/A 1.090 in

R Rad Max

N/A 0.040 in

T Across Hex. Ref.

N/A 0.500 in

Z Max

N/A 0.045 in

Minimum available grip length

N/A -150

Recommended Hole Size

N/A 0.375-0.378

J Dia Min

N/A 0.575 in

K Max

N/A 0.625 in

Break off Limits <5>

N/A 0.050-0.053

Tensile Structural Failure (Min)

N/A 5000 lb

Double Shear Min

N/A 16450 lb

Locking Torque Min

N/A 4.000 lb-in0.452 N-m

Material and Heat Treat

N/A Nut: A-286 per chemical requirements of AMS 5731, AMS 5732, AMS 5734 and AMS 5737. Heat treated as required for performance.
Screw: A-286 per the chemical requirements of AMS 5731, AMS 5732, AMS 5734 and AMS 5737. Heat treated as required for performance.
Sleeve: 304 stainless steel per AMS 5639, heat treated as required for performance.
Insert: Acetal per ASTM D4181
DryvcapTM: Mild steel.

Finish

N/A Nut, Sleeve & Screw: Passivate per AMS-QQ-P-35. KAL-GARD ANN-RO #1013 conversion coating optional.
Insert: None
DryvcapTM: Corrosion resistant coating, color black.

Lubricants

N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol per MIL-L-87132.

Applicable Specification

N/A 1.Procurement specification: FCBF200
2.Special lube and finish: FCBF202

Material Type

N/A A286 CRES

Rated Shear Strength

N/A 75 KSI

Headstyle

N/A Protruding

Notes

N/A 2.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D.
<3>Alternate head marking: "VS" and "O"
4.Composite blind fasteners with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufacrure´s option. Contact Fairchild Engineering.
<5>An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates midified break-off limits of +.053/-.050. "EX: FCBF2120( )-6L200".
<6>Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to minimum recommended hole. Insertion force shall not exceed 5.0 lbs.