close
close
ACCU-LOK® II blind fastener for composite application - 130° flush head titanium.
Unit of Measure

Dash Number (Grip)

N/A 1300

Grip Range - Min. Grip

N/A 1.250 in

Grip Range - Max. Grip

N/A 1.300 in

Grip Range

N/A 1.250-1.300 in

A Ref

N/A 0.332 in

B Ref

N/A 0.296 in

D

N/A 0.165 in

E Max

N/A 0.164 in

F Wrench Flats

N/A 0.085 in

G Ref

N/A 0.017 in

H Ref

N/A 0.039 in

L Ref

N/A 0.512 in

R Rad

N/A 0.030 in

S Max

N/A 0.009 in

T Across Hex Ref

N/A 0.375 in

Minimum available grip length

N/A -100

Recommended Hole Size

N/A 0.165-0.168

J Dia Min

N/A 0.250 in

K Max

N/A 0.300 in

Break off Limits <5><6>

N/A 0.050-0.053

Tensile Structural Failure (Min)

N/A 900 lb

Double Shear Min

N/A 3150 lb

Locking Torque Min

N/A 1.000 lb-in0.113 N-m

V Gage Prot.

N/A 0.012 in

W

N/A 0.283 in

Material and Heat Treat

N/A 1.Nut: 6AL-4V titanium per AMS4928 or AMS4967; heat treated per MIL-H-81200 to 95 ksi shear strength minimum. Maximum hydrogen content 125 ppm.
2.Screw: A286 per AMS 5731, AMS 5732 or AMS 5737; heat treated to 175 ksi tensile minimum.
3.Sleeve: 304 stainless steel per AMS 5639, heat treat as required for performance.
4.Insert: Acetal per ASTM D4181.
5.DryvcapTM: Mild steel (color gray)

Finish

N/A 1.(-) Nut: KAL-GARD ANN-RO #1012 conversion coating or phosphate flouride per AMS2486 may be used at manufacturer´s option.
2.Sleeve and screw: Passivate per AMS 2700, KAL-GARD ANN-RO #1013 conversion coating optional.
3.Insert: None
4.Dryvcap

Lubricants

N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol per MIL-L-87132.

Applicable Specification

N/A 1.Procurement specification: FCBF200
2.Special lube and finish: FCBF202

Material Type

N/A Titanium

Rated Shear Strength

N/A 75 KSI

Headstyle

N/A 130° Flush

Notes

N/A 5.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose and O.D:
<6>Alternate head marking: ("VS") and "2013".
7.Composite blind fasteners with selected combinations of the above lubrications and finishes are specially coded amd may be substituted for equivalent non-coded parts at manufactures option. Contact Howmet Fastening Engineering Systems.
<8>An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates modified break-off limits of +.053/-.050.
<9>An "LL" in place of the dash (-) between the diameter dash number and the grip dash number designates midified break-off limits of +.003/-.100.
<10>Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to a minimum recommended hole. Insertion force shall not exceed 5.0 lbs.