Howmet
Dash Number (Grip) |
N/A 1650 |
Grip Range - Min. Grip |
N/A 1.600 in |
Grip Range - Max. Grip |
N/A 1.650 in |
Grip Range |
N/A 1.600-1.650 in |
A |
N/A 0.416 in |
D |
N/A 0.199 in |
E Ref |
N/A 0.199 in |
F Wrench Flats |
N/A 0.113 in |
G Ref |
N/A 0.027 in |
H |
N/A 0.070 in |
L Ref |
N/A 0.575 in |
R Rad |
N/A 0.030 in |
Z Max |
N/A 0.030 in |
g |
N/A 0.050 in |
c Max |
N/A 0.027 in |
r |
N/A 0.035 in |
Minimum available grip length |
N/A -100 |
Recommended Hole Size |
N/A 0.199-0.202 |
J Dia Min |
N/A 0.300 in |
K Max |
N/A 0.350 in |
Break Off Limits |
N/A 0.000-0.103 |
Tensile Structural Failure (Min) |
N/A 1400 lb |
Double Shear Min |
N/A 4600 lb |
Locking Torque Min |
N/A 1.500 lb-in0.170 N-m |
Material |
N/A
1.Nut: 6AL-4V titanium per AMS 4928 or AMS 4967. 2.Screw: A286 per AMS 5731, AMS 5732 or AMS 5737. 3.Sleeve: 304 stainless steel per AMS 5639. 4. Insert: Acetal per ASTM D4181. 5. Drive nut: Mild steel. 6. Drive cylinder: Mild steel. |
Heat Treat |
N/A
1.Nut: Heat treat per MIL-H-81200. 2.Screw: Heat treated to 175 ksi tensile minimum. 3.Sleeve: Heat treated as required for performance. |
Finish |
N/A
1.Nut: KAL-GARD ANN-RO #1012 conversion coating or phosphate fluoride per AMS 2486 may be used at manufacturer´s option. 2.Screw: KAL-GARD ANN-RO #1013 conversion coating optional. 3.Sleeve: Passivated per AMS 2700. 4.Insert: None Drive nu |
Lubricants |
N/A 1. The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, parafin wax, or cetyl alcohol per AS87132. |
Applicable Specification |
N/A
1.Procurement specification: FCBF200 2.Special lube and finish: FCBF202 3.ACCU-LOKTM blind fastener: FCBF204 |
Material Type |
N/A Titanium |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A Protruding |
Notes |
N/A
6. Locking feature consist of three (3) indentation located 120° apart on the periphery of the nut component approximately .040 above intersection of the nut nose angle O.D. <7> Alternate heading marking ("VS") and "2010". 8. Composite blind fasteners with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufactures option. Contact Howmet Fasteners Systems. <9> Distortion shall be not prevent insertion of the fastener into a ring gage of length equal to one diameter and hole diameter equal to a minimum recommended hole. Insertion force shall not exceed 5.0 lbs. |
