Howmet Fastening Systems
Howmet Fastening Systems
Phone: Sales +1 800 992 4444
Technical Support +1 310 784 6409
Email: HFSTechSupport@howmet.com
Website: www.hfs.howmet.com
Print Back

Blind Bolt Fastener, High Strength, Friction Thread Lock, Threaded, 130° Flush Shear Head, Close Tolerance Shank, Titanium/A-286 (95 KSI Shear)
Unit of Measure

Specifications

Nominal Diameter

 N/A 0.1900 Inch

Nominal Diameter No.

 N/A 06

A Theo Inter Nom Ref.

 N/A 0.3868 Inch

A' Dia. Min.

 N/A 0.318 Inch

J Max.

 N/A 0.015 Inch

C Driver Length Ref.

 N/A 0.250 Inch

D Shank Dia.

 N/A 0.1885 Inch0.1895 Inch

E Spline O.D. Ref.

 N/A 0.180 Inch

F Head Height Max.

 N/A 0.047 Inch

R Radius ± .005

 N/A 0.025 Inch

G Gauge Dia.

 N/A 0.2980 Inch0.2982 Inch

H Gauge Height

 N/A 0.0192 Inch0.0222 Inch

Min. Single Shear Strength1

 N/A 2690 lb

Min. Tensile Strength1

 N/A 1410 lb

K Lead-In Dia.

 N/A 0.1804 Inch0.1830 Inch

M Ref.

 N/A 0.065 Inch

BD Dia. Min. - Extended Grip6

 N/A 0.238 Inch

BD Dia. Min. - Design Grip

 N/A 0.247 Inch

Design Grip Range Min.11

 N/A 0.751 Inch

Design Grip Range Max.11

 N/A 0.812 Inch

L10

 N/A 1.169 Inch1.169 in

Material Nut Body

 N/A A286 CRES per Chemical Composition AMS 5737 or 5732

Material Core Bolt

 N/A 6Al-4V Titanium per AMS 4967 or 4928

Finish Nut Body

 N/A Passivate per AMS 2700 Type 2 or Type 8 & Cetyl Alcohol Lube per AS87132 at Manufacturer's Option

Finish Core Bolt

 N/A Incotec Tec-Lube Dry Film Lube per AS5272 or Equivalent & Cetyl Alcohol Lube per AS87132 at Manufacturer's Option

Procurement Specification

 N/A T0108

Complete Installation Tool

 N/A ETT2000-06 ETT2026-06

Installation Nose Only

 N/A ETT2000-06N

Recommended Installation Hole Sizes

 N/A 0.190 Inch0.193 Inch

Installed Weight

 N/A 6.76 Lbs/1000

Notes

N/A

Technical Specifications

  1. Single shear testing shall be in accordance with the requirements of NASM 1312-20 and applies to grips 05-05 min, 06-06 min, 08-07 min, 10-09 min and 12-10 min and longer. Tensile strength testing shall be in accordance with requirements of NASM 1312-8 and applies to grips 05-06 max, 06-07 max, 08-08 max, 10-10 max and 12-12 max and longer.
  2. Dimensions are in inches and are to be met after finish.
  3. 3 indentations 120° apart to provide thread lock.
  4. Blind side head may be installed on 5° maximum slope.
  5. The average smallest and largest observed values on the same specimen shall be equal to or greater than the stated minimum.
  6. Extended grip "BD min" value applies to a part driven .010"±.003" above the design maximum grip.
  7. Sleeve dia. may be up to .0003" oversize in band anneal zone. Zone extends from approximately blind end - .525" for the -06 Dia. and .635" for the -08 Dia.
  8. Identification: -06 and -08: manufacturer's ID, marking indented .010 maximum, arrangement optional.
  9. Transition, optional radius or chamfer.
  10. Consult HFS for availability of longer grip lengths.
  11. Grip range is reduced for 06 diameter.