Dash Number (Grip) |
N/A -190 |
Grip Range - Min. Grip |
N/A 0.669 in |
Grip Range - Max. Grip |
N/A 0.748 in |
Grip Range |
N/A 0.669-0.748 in |
Nominal Dia |
N/A 0.236 in |
A Dia Max |
N/A 0.472 in |
B Dia Min |
N/A 0.425 in |
D Dia |
N/A 0.236 in |
E Dia Max |
N/A 0.235 in |
F Wrench Flats |
N/A 0.121 in |
G Ref. |
N/A 0.035 in |
H Ref. |
N/A 0.054 in |
L Ref. |
N/A 0.800 in |
R Rad |
N/A 0.028 in |
S Max |
N/A 0.011 in |
T Across Hex Ref. |
N/A 0.375 in |
V Gage Prot. |
N/A 0.018 in |
W Gage Dia |
N/A 0.398 in |
Recommended Hole Size |
N/A 0.2362-0.2392 |
J Dia Min |
N/A 0.360 in |
K Max |
N/A 0.490 in |
Break off Limits <4> |
N/A 0.050-0.053 |
Tensile Structural Failure (Min) |
N/A 1956 lb |
Double Shear Min |
N/A 6740 lb |
Prevailing Torque Min |
N/A 2.500 lb-in0.280 N-m |
Material and Heat Treat |
N/A
Nut: 6AL-4V titanium per AMS 4928 or AMS 4967; Heat treated per MIL-H81200 to 95 ksi shear strength minimum, maximum hydrogen 125 ppm Corebolt: A-286 per AMS 5731, AMS 5732 or AMS 5737; heat treated to 175 ksi tensile min. Sleeve: 304 stainless steel per AMS 5639; heat treated as required for performance. Insert: Acetal per ASTM D4181 DryvcapTM: Mild steel. |
Finish |
N/A
(-) Nut: KAL-GARD ANN-RO #1012 conversion coating or phosphate flouride per AMS 2486 may be used at manufacturer´s option. Sleeve & Corebolt: Passivate per AMS-QQ-P-35. KAL-GARD ANN-RO #1013 conversion coating optional. Insert: None Dryvcap |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol. |
Applicable Specification |
N/A
Procurement specification: FCBF208 Special lube and finish: FCBF202 |
Material Type |
N/A Titanium |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A 130° Flush |
Notes |
N/A
2.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D. 3.Composite blind fastener with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufacturer´s option. Contact Fairchild Engineering. <4> An "L" in place of the dash (-) between the diameter and dash number and the grip dash number designates modified break-off limits of +.053/-.050. "EX: FCBF7013-6L200". <5> Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and diameter equal to a minimum recommended hole. Insertion force shall not not exceed 5.0 lbs (22.24 Newtons). |