Howmet
Dash Number (Grip) |
N/A 450 |
Grip Range - Min. Grip |
N/A 0.400 in |
Grip Range - Max. Grip |
N/A 0.450 in |
Grip Range |
N/A 0.400-0.450 in |
A Hex |
N/A 0.375 in |
B Min |
N/A 0.409 in |
D |
N/A 0.260 in |
E Max |
N/A 0.260 in |
F Wrench Flats |
N/A 0.135 in |
G Ref |
N/A 0.055 in |
H |
N/A 0.090 in |
L Ref |
N/A 0.700 in |
R Rad |
N/A 0.030 in |
T Across Hex Ref |
N/A 0.375 in |
Minimum available grip length |
N/A -150 |
Recommended Hole Size |
N/A 0.260-0.263 |
J Dia Min |
N/A 0.400 in |
K Max |
N/A 0.450 in |
Break off Limits <5><7> |
N/A 0.050-0.053 |
Tensile Structural Failure (Min) |
N/A 2100 lb |
Double Shear Min |
N/A 7900 lb |
Locking Torque Min |
N/A 2.500 lb-in0.282 N-m |
Material and Heat Treat |
N/A
1.Nut: 6AL-4V titanium per AMS 4928 or AMS 4967; heat treated per MIL-H-81200 to 95 ksi shear strength minimum. Maximum hydrogen content 125 ppm. 2.Screw: A286 per AMS 5731, AMS 5732 or AMS 5737; heat reated to 175 ksi tensile minimum. 3.Sleeve: 304 stainless steel per AMS 5639, heat treated as required for performance. 4.Insert: Acetal per ASTM D4181 5.DryvcapTM: Mild steel (color gray). |
Finish |
N/A
1.(-) Nut: KAL-GARD ANN-RO #1012 conversion coating or phosphate flouride per AMS 2488 may be used at manufacturer´s option. 2.Sleeve & screw: Passivate per AMS 2700, KAL-GARD ANN-RO #1013 conversion coating optional. 3.Insert: None 4.Dryvcap< |
Lubricants |
N/A The following lubricants may be applied to any or all components in any combination as required for performance unless otherwise specified: Dry film lube per AS5272, Type I, everlube #812, paraffin wax, or cetyl alcohol per MIL-L-87132. |
Applicable Specification |
N/A
1.Procurement specification: FCBF200 2.Special lube and finish: FCBF202 |
Material Type |
N/A Titanium |
Rated Shear Strength |
N/A 75 KSI |
Headstyle |
N/A Hex Protruding |
Notes |
N/A
5.Locking feature consists of three (3) indentations located 120° apart on the periphery of the nut component and approximately .040" above intersection of the nut nose angle and O.D. <6>Alternate head marking: ("VS") and "2011". 7.Composite blind fasteners with selected combinations of the above lubrications and finishes are specially coded and may be substituted for equivalent non-coded parts at manufactures option. Contact Howmet Fastening Engineering Systems. <8>An "L" in place of the dash (-) between the diameter dash number and the grip dash number designates modified break-off limits +.053/-.050. "EX: FCBF2111( )-6L200. <9>Distortion shall not prevent insertion of the fastener into a ring gauge of length equal to one diameter and hole diameter equal to a minimum recommended hole. Insertion force shall not exceed 5.0 lbs. <10>High break parts denoted by an "H" in the part number as follows |
